<optgroup id="s2ae4"><div id="s2ae4"></div></optgroup>
<center id="s2ae4"><wbr id="s2ae4"></wbr></center>
<code id="s2ae4"></code>
<optgroup id="s2ae4"></optgroup><optgroup id="s2ae4"><small id="s2ae4"></small></optgroup>
<optgroup id="s2ae4"><div id="s2ae4"></div></optgroup>
<center id="s2ae4"></center>

Megan:188 9563 9870

Bengbu Jixin Communication Machinery Co., Ltd.
  • 1
  • 2
  • 3
  • 4
Causes of failure of optical fiber head end connection
2016-3-31
source:unknown
clicks:  1691        作者:未知
  • Possible causes of the failure of the connection include:

    1. pollution

    2..fiber fragmentation

    3. bad cutting or breaking of optical fiber

    4. pre polishing optical fiber and cutting the fiber splice gap is too large

    5. over biased optical fiber cutting angle.

    Fault location: pollution

    The possible reasons for the pollution of optical fiber connector are:

    The use of contaminated cutting tools (wiping tool surface by anhydrous alcohol);

    The complete cut again after wiping the fiber (never wipe fiber after being cut);

    I will connect the head or the fiber in the dusty surface In the dusty environment;

    It is inserted into the optical fiber has been broken, excessive force;

    It should be noted that if the contamination is brought into the optical fiber connector, especially after contact with the gel, it will be difficult to be removed, which means that the end of the fiber connector is scrapped.

    Fault location: fiber fragmentation

    It may cause the fiber fragmentation:

    The insertion of excessive force produced fiber debris pollution;

    It is inserted into the optical fiber has been broken due to fragmentation ] embedded fiber fragmentation will lead to the optical gap and the optical breakdown and embedded optical fiber fragmentation is very difficult to be cleared out and the optical fiber connector will be scrapped.

    Fault location: bad cutting or breaking of optical fiber

    The reasons for bad or broken fiber:

    The blunt or rupture of the cutting blade - normal cutting fiber;

    The cutting tool on the bending of the tongue scale applied bending force excessive concentration on optical fiber;

    The fiber bending bending radius is too much or too tight;

    I did not force or force in cutting;

    When no debris is produced or not contaminated, this failure allows the fiber optic connection head to be re cut and connected again.

    Fault location: the preset grinding and cutting of the fiber optic fiber splicing gap is too large

    By connecting the large gap of reasons:

    The fiber cutting length is too short;

    The fiber is not fully imported, or terminated by the pull back;

    In the outdoor cable joint when the fiber is pushed back into a protective sleeve;

    We have a large gap fiber are only allowed to correct.

    Fault location: over biased optical fiber cutting

    In the continuous scene, the cutting angle is too difficult to be detected.

    The factors that lead to the angle of cutting are too:

    The cutting tool on the tongue bending bending force is applied too much concentrated on optical fiber;

    The fiber bending bending radius is too large or too tight;

    I did not force or force in cutting After the general optical fiber cutting, the typical cutting angle is 1-3 degree, the use of precision optical fiber cutting knife;

    Through the introduction of the above, it is not difficult to see non polished fiber field connection for the succeeding process and operation technology of sensitive, non grinding field termination technology the key lies in the installation personnel must maintain the unity of the cutting and end connection technology, and for the installation process is controlled and avoid rework, in stead of always through detection (such as visible light detection) to establish in the termination process of confidence, reduce connecting the risk of failure.

top comments
  • no information

identifying code: Verification code not see clearly? Please click Refresh verification code
  Product Category 

Add.:No.8318, Huangshan Avenue, Bengbu City, Anhui Province, China233010
Foreign Trade Dep.: [email protected],E-mail:[email protected] 
   Website:www.www.zldhj.com
Copyright(C) 2016-2019 Bengbu Jixin Communication Machinery Co., Ltd
 Record No:皖ICP備11019128號-1

Official agent for FOB account:
BENEFICIARY NAME(收款人名稱 59A):CHALLENGE INDUSTRIAL LIMITED 
CORRESPONDENT BANK: BANK OF AMERICA N.A.NEW YORK BRANCH 
(中間行 54/56A) SWIFT BIC:   BOFAUS3N 
BENEFICIARY BANK:  ZHEJIANG CHOUZHOU COMMERCIAL BANK 
(收款行 57A) SWIFT BIC:   CZCBCN2X 
A/C NO(帳號 59A):NRA15602142010500016781 
ADDRESS (地址): 1708 NO32 LANE 975 DALIAN RD SHANGHAI 200092 CHINA 
亚洲中文字幕无码一区|影音先锋你懂的|人妻无码av中文系列久久免费|春色,亚洲,图片,小说|大香伊蕉国产AV|中文欧美亚洲欧日韩|中文无码人妻影音先锋